from basics to Advanced

  • FEA Articles
    • CAE for beginners
    • Open-source FEA
    • Basics of mechanics
    • Buckling, Nonlinear FEA & Advanced Tips
    • Design Failure
    • Heat Transfer
    • Meshing Techniques
    • Modal, Frequency and Dynamic Analysis
    • Stress & Safety Factor
    • FEA Singularities
  • FEA Courses
    • Learn FEA with this Free Video Course
    • Your first FEA simulation…
  • FEA Guides
    • Thermal Analysis Guide
    • Dynamic Analysis (with Damping) Guide
    • Fatigue Analysis Guide
  • FEA Tutorials
    • FEA Webinars
    • Salome Meca and Code Aster Tutorials
    • Ansys Video Tutorials
    • midas NFX
    • midas GEN
    • OnScale Tutorials
  • Programming
    • Python
    • Fortran
    • Language C
  • More
    • About Me
    • Podcast
    • FEA Books
    • FEA Knowledge Base
    • Unit Converter
  • Log In

[Salome Automation 5] Batch Process Aster simulations with a loop in YACS

November 21, 2020 by Cyprien 1 Comment

[Salome Automation 5]   Batch Process Aster simulations with a loop in YACS

The 5th tutorial of the series is here. In the previous videos, I have shown how to automate 1 simulation using parameters to make it parametric. Now… no one wants to run one sim, wait for it to finish, change the parameters and try again. That’s why I will show you now how to make […]

Filed Under: Open-source, Salome-Meca, YACS Tutorials Tagged With: automation, salome, YACS

[Salome Automation 4 ] Automating Paravis Post-processing with YACS

November 14, 2020 by Cyprien Leave a Comment

[Salome Automation 4 ] Automating Paravis Post-processing with YACS

The 4th part of the YACS tutorial series is here… Post-processing, Finally! ;-) First, I’l come back briefly on the previous video and show you how to correct the small assignment I gave you… to set up a control node that will write the comm file to control Code_Aster’s input deck with parameters! I hope […]

Filed Under: Salome-Meca, YACS Tutorials Tagged With: automation, open-source FEA, Salome Meca, YACS

[Salome Automation 3 ] Automating Code Aster Simulation with YACS

November 6, 2020 by Cyprien 1 Comment

[Salome Automation 3 ] Automating Code Aster Simulation with YACS

The next video of the YACS series “Salome Automation” is here and we are going to learn together how to automate a Code_Aster simulation with YACS… Cool, eh? This is the 3rd video of the series, so I won’t go back on the basics I taught in the video 1 and in the video 2 […]

Filed Under: Open-source, Salome-Meca, YACS Tutorials Tagged With: automation, code_aster, YACS

Salome Automation 2 – Automating Geometry and Mesh Creation with YACS

October 24, 2020 by Cyprien 2 Comments

Salome Automation 2 – Automating Geometry and Mesh Creation with YACS

I promised that I would show you how to automate Salome, including geometry, mesh, simulation and post-process! So, here you go ;-) Let’s start with the Geometry and the Mesh today. Nothing too fancy, just a 3D plate… but that’s how great project start, from small plates ! If you haven’t watched the first video […]

Filed Under: Open-source, Salome-Meca, YACS Tutorials Tagged With: automation, Salome Meca, YACS

[Salome Automation 1] Introduction to YACS Module & Beginner Tutorial

October 2, 2020 by Cyprien 4 Comments

[Salome Automation 1] Introduction to YACS Module & Beginner Tutorial

Have you ever wanted to automate your simulation process in Salome? The good news is that you can with a little known module called YACS. This module is a bit difficult to use at first without have received a training about it because the interface isn’t very intuitive (It’s open-source…), but once you saw how […]

Filed Under: Salome-Meca, YACS Tutorials Tagged With: salome, YACS

Other FEA articles:

  • What is frequency response analysis in FEAWhat is frequency response analysis in FEA
  • What if CAE simulation could change the world ? – NAFEMS CAEGuy
  • What causes singularity in your FE model?What causes singularity in your FE model?
  • Buckling in FEA: A simple explanation and demonstrationBuckling in FEA: A simple explanation and demonstration
  • How to display energy intensity results with calc aint in Onscale AnalystHow to display energy intensity results with calc aint in Onscale Analyst

About me

I’m an Mechanical Engineer who would like to share his passion on Finite Element Analysis to help other Engineers. Read more…

View Cyprien Rusu's profile on LinkedIn

Find videos about FEA

[Openfoam Tutorial 2] Lid-Driven Cavity Flow
[Tutorial 1] How to Install OpenFoam on Linux and Windows
Running a YAC scheme without the Salome GUI
1/123
Next»
By PoseLab
My YouTube Channel

© Copyright since 2013 feaforall · All Rights Reserved