Hundreds of engineers asked me about buckling and every time, the way that I explain it makes them understand almost immediately how it works.

That’s what I’ll share with you today for the beginning of 2017 :)

Buckling is very simple to understand with the simple following example.

Imagine that you are pushing a parallelepipedic shape of metal with both hands on each end.

**Will you ever be able to break it?**

I am sure that you guessed by experience that you won’t…

But why?

Simple…

The load that you apply with your hands will never cause enough stress to exceed the material resistance that will make it yield.

Or said simply: **You are not strong enough**.

Second question:

Suppose that I just change one parameter in this experiment… I decide to reduce the thickness of my parallelepipedic shape to 0.5 mm

You now have something which looks exactly like a ruler in your hands

What happens now if you apply exactly the same pressure on both sides with your hands?

Do you have the confidence that you can break it now?

Why is that?

The material is the same, the load is the same, applied in the same direction right?

The answer is simple…

This time, it breaks not because the loads exceeded the maximum stress resistance.

It breaks because another phenomenon linked to the geometry of the part….

And it happens for all the parts that have a small thickness (typically…shells)

This phenomenon is called **buckling**.

So, without knowing it, we all have at least once buckled and broken a ruler in our chilhood (several in my case ;-) )

## How do you explain failure by Buckling?

Let’s go back to the experiment and think hard.

If you take a ruler and apply a load exactly in the same plane on both sides and if you suppose that the load is a perfect linear load with a perfect orientation…. will it break the ruler?

In **theory**, no.

It should compress, and the cross section should change a bit due to the poisson’s effect.

(That’s why…when you do a linear static analysis you will see exactly that and you won’t observe the buckling. We’ll see that in the video below)

But in **practice**, yes!

Buckling is something in relation with the difference between classic linear static theory and reality here.

We suppose the load had a perfect orientation…

In reality, in almost never happens (Perfection only exists in our heads and in formulas we created from models).

There is always a very small, **almost insignificant +α** of the load in another direction.

This +α is what creates an instability in the system and causes the ruler to buckle.

Because more you push and more the +α becomes important… so important in fact that it causes the ruler to break MUCH before it’s material resistance limit.

## Why is buckling so dangerous?

Think about it for one second.

You built a system which is theoretically okay.

You tested all the loading scenarios and every light is green. It will never fail.

Then…

Someone using your product doesn’t calibrate right how the system is fixed… maybe he fixes it on a ground which is not exactly horizontal… even with a 0.5 mm of difference.

And your wonderful system starts to buckle and fails.

Wouldn’t that be dangerous?

The guy will probably be angry and will start to call the support service to get back his money quickly…

You can tell him that you checked everything and everything was perfectly okay in your testing conditions and inside your computer model.

Will he listen? Probably not.

Maybe there will even be lives on the line.

If the system is something huge like a crane or a structural element of a building… then it becomes really dangerous.

Yep, buckling is something serious man…

## How to calculate the buckling load for a simple pin-joined elastic beam

With a so dangerous failure mode creating so much potential damage, you guess that engineers have been developing models over time to try to calculate what really happens.

For a simple beam with a very small thickness, what happens is clear like water.

What we want to know is the minimum load that will cause buckling to happen.

We generally call it the **lowest buckling load**.

(Why “lowest”, we’ll see that in an instant…)

This load is important because it causes failure much BEFORE the usual material failure.

There are several ways to do the calculation, but I’d like to show you one of them called the **adjacent equilibrium method**.

In this method, the buckling load is calculated by considering a slightly bent configuration of a pinned-pinned elastic beam.

## Why are there several buckling modes?

You saw that I took n=1 in the previous example, that’s because I calculated the buckling load of the first buckling mode, also called the lowest or fundamental buckling load.

There are other buckling modes… everything depends on how your beam is constrained.

If it is prevented to buckle with the shape of the first buckling mode because it is prevented to do so by a pin for example, then it will still buckle, but along the second buckling mode.

**How to do buckling in FEA?**

I almost forgot this blog is about FEA :)

**Linear Buckling** in FEA is actually very simple

(Nonlinear buckling is much more tricky…)

Here’s the video:

**Is there more to know about buckling?**

You bet there is :)

As always… when you start to understand something, you discover there’s plenty more things to understand about it that you weren’t aware of!

This article gives a very simple explanation of the concept but there are much more things to know about buckling.

For example, there is linear and nonlinear buckling…

I talked about it in a webinar I did previously, you can watch it here if you are interested

That’s all for today!

/////////////////////////////////////////////////////

You maybe noticed that I wrote a lot of great educational article… that’s because I really want to contribute and help engineers who are new to FEA to understand those concepts better and faster!

I am not hiding that it takes a lot of efforts to write all that, so…

**If you like this article, there are 3 things you can do for me:**

1- Help me to share this article on **Linkedin, facebook, twitter** or in your habitual forum to help more people understand buckling (use the share button on the left of the article).

2- **Let me know in the comments** what you learned from it and what you would like to learn even further so I can write more on the topic

3- **Join the newsletter** (if you are not already subscribed), I’ll send you everything I write (and much more) by email!

Thank you for reading!

–Cyprien

Trần Huy Thông says

Thanks you so much for this article

Sri Harsha says

Thanks for sharing the article :-)

Abhinav T says

Thanks

SIDDHESH V. NIKAM says

Very good article. It’s like a “POCKET SCIENCE”, wonderful. Very simple to understand for the freshers.

Cyprien says

Thank you Siddhesh! Glad you like it!

imane says

thank you for the article and the Video

Devrim says

Buckling is a beautiful behavior of a geometry of material with this you know until which level a form can define the function limits. This is nice nature.

Cyprien says

Thank you Devrim!

Kalpesh says

The article of buckling os very good.

If it will include more detailed about modes its relation, what is buckling factor how mode is related to it,where to stop in FEA in terms of modes then it will finish with perfect.

Tim says

Does the linear buckling analysis only depend on the axial force in the member ?

Ayesha says

Thanks 4 sharing..and plz tell me how to apply simply support b.c and clamped b.c on shell in abaqus .. wait for your helping reply plz

Saiteja says

Thank you so much sir for making a post on buckling. Currently, I am working on buckling. This post means a lot to me

Santhosh says

Easily understandable! Thank you Cyprin for sharing it!

Jamal says

Very clear approach to understand buckling for the students. I think I will use it to explain buckling in the classroom.

Cyprien says

Thanks Jamal! Glad that this will help your students to understand better buckling.

Santo says

Doesn’t the way the forces are applied make this more of a column than a beam? I’d be more interested in the process of determining the minimal thickness of vertical walls in horizontal beams, with the very standard setup of 2 supports and vertical loads.

For example, let’s say we have 2 steel rectangular box sections – 200x100x8 and 300x100x4 mm. They both have almost the same Wx value so the stresses in their upper and lower sides / should be similar. At the first glance, the latter is the better option because it weighs less. But there is a catch – surely we can’t trade height for wall thickness indefinitely. At some point the beam will definitely buckle.

How do we determine that?

Red Phosphorus says

Great article! Thanks for sharing it!

narasimha says

excellent…very good explanation of concepts

Sang Le says

Thank you very much for your article. Could you teach more about buckling failure of Shell element ?

Vahid says

Thanks for the article. I really liked the simple explanation. Only one point: i can not open the videos of your website using iOS!

Cyprien says

Weird, it works on my iPhone. This video is on Youtube.

Is Youtube banned in your country or company?

Jack says

Great Article! Thank You!

divyadhanan says

Thank you so much for the article! Makes understanding concepts insanely easy :)